v50 Steam/Premium information for editors
- v50 information can now be added to pages in the main namespace. v0.47 information can still be found in the DF2014 namespace. See here for more details on the new versioning policy.
- Use this page to report any issues related to the migration.
This notice may be cached—the current version can be found here.
Editing v0.34:Tile attributes
Jump to navigation
Jump to search
Warning: You are not logged in.
Your IP address will be recorded in this page's edit history.
You are editing a page for an older version of Dwarf Fortress ("Main" is the current version, not "v0.34"). Please make sure you intend to do this. If you are here by mistake, see the current page instead.
The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
| Latest revision | Your text | ||
| Line 18: | Line 18: | ||
The entire [[Location|fortress site]] starts out as {{DFtext|Inside |6:0}}{{DFtext|Dark Subterranean|0:1}}. After that, a ray for {{DFtext|Outside|3:1}} and a ray for {{DFtext|Light |6:1}}{{DFtext|Above Ground|2:1}} falls straight down from the highest [[z-level]] for every (x,y) position on the local map, changing each tile's modifiers until something that blocks that particular "ray" is encountered. Due to this behavior, any of the previous three tile combinations will never be encountered in the same (x,y) position on a lower z-level than a higher numbered combination. | The entire [[Location|fortress site]] starts out as {{DFtext|Inside |6:0}}{{DFtext|Dark Subterranean|0:1}}. After that, a ray for {{DFtext|Outside|3:1}} and a ray for {{DFtext|Light |6:1}}{{DFtext|Above Ground|2:1}} falls straight down from the highest [[z-level]] for every (x,y) position on the local map, changing each tile's modifiers until something that blocks that particular "ray" is encountered. Due to this behavior, any of the previous three tile combinations will never be encountered in the same (x,y) position on a lower z-level than a higher numbered combination. | ||
| − | == Outside vs | + | == Outside vs Inside == |
This attribute is determined by whether there is a roof of some kind over a tile. Weather only affects tiles which are ''Outside''. Almost any kind of geometry will block the ''Outside'' ray including natural and constructed [[wall]]s, [[floor]]s, [[stair]]s, and [[fortification]]s, and open and closed [[bridge]]s, [[grate|floor grates]], [[bars|floor bars]], and [[hatch]]es. A tile which is ''Outside'' will always be ''Light Above Ground'', but an ''Inside'' tile may be either ''Light Above Ground'' or ''Dark Subterranean''. | This attribute is determined by whether there is a roof of some kind over a tile. Weather only affects tiles which are ''Outside''. Almost any kind of geometry will block the ''Outside'' ray including natural and constructed [[wall]]s, [[floor]]s, [[stair]]s, and [[fortification]]s, and open and closed [[bridge]]s, [[grate|floor grates]], [[bars|floor bars]], and [[hatch]]es. A tile which is ''Outside'' will always be ''Light Above Ground'', but an ''Inside'' tile may be either ''Light Above Ground'' or ''Dark Subterranean''. | ||
| − | == Light vs | + | == Light vs Dark and Above Ground vs Subterranean == |
Currently these two attributes are determined in exactly the same way. Once an area is exposed to the outside world, it is ''Above Ground'' and ''Light'' (and thus channeling this tile will make the tile below it also ''Above Ground'' and ''Light''). Even after being covered up again, it will remain this way. This allows growing outdoor crops inside safely. | Currently these two attributes are determined in exactly the same way. Once an area is exposed to the outside world, it is ''Above Ground'' and ''Light'' (and thus channeling this tile will make the tile below it also ''Above Ground'' and ''Light''). Even after being covered up again, it will remain this way. This allows growing outdoor crops inside safely. | ||